How to reduce the impact for the environment effectively during the cutting of the fiber laser cutting machine?

Compared with traditional cutting way, the cutting way of fiber laser cutting machine has big advantages. But the fiber laser cutting machine can produce dust,dense smoke,intense laser beam and so on when it is cutting. Not only these cutting derivatives has an affect on the operator’s health,but also it also not good for the environment.

So what methods can avoid these problems effectively when the fiber laser machine is working? According to the production research experience for more years and the customers’ feedback, the following effective methods are listed by owin fiber laser for your reference:

  1. Exhaust

It is usually local exhaust in the fiber laser cutting industry. The fiber laser cutting machine is installed exhaust fan,which can do extraction in the fixed position where the operator is standing during using the fiber laser cutting machine.So the location where operators is standing will not be exposed to harmful gases and smoke.

But this efficiency of this way is very low and the effect is also not good. Because smoke dust and other harmful gases are diffuse to the whole environment from the source of the production. The speed is very slow from local exhaust. And it will also extract the air which has been polluted from other places,which can not achieve the desired result.

  • Ventilation

It usually has two ways for ventilation. One is natural ventilation. Another is mechanical ventilation.

Natural ventilation is usually for the fiber laser cutting working out of the door or in the open space.The harmful gases can be blown away by the natural wind produced from the cross-ventilation.

But for the fiber laser machine working indoor, the air can be clean by mechanical ventilation.The customer can install industrial exhaust fan on the roof or on the wall of the factory,which can exhaust air from indoor to outdoor.It can reduce the concentration of the smoke dust in the workshop.

3.Industrial dust collector

This is the most popular and environmentally friendly method currently.

The air in the factory can be filtered by the dust collector or smoke purifier when the fiber laser cutting machine is working.This way is more in line with the requirement of environmental protection.

The smoke dust and harmful gases can be collected by the pipes in the fiber laser cutting machine and transport to the dust hood of the dust collector installed near the fiber laser machine.It not only achieves the request of the environmental protection and ensure the operator’s health.But also it can also ensure the surface cleanliness of the cutting work pieces.

Jinan owin cnc equipment Co.,LTD is a private company,which have

Research department,Design department,Professional Production department,Sales department, After Sale Service department,Accounting department.The main products are fiber laser cutting machine,fiber laser welding machine,fiber laser cleaning machine,fiber laser marking machine,cnc router and so on equipment,which are widely used in electronics, automotive, sheet metal, profile, advertising, furniture and other fields.

Owin cnc is adhering to the “BEST FAST” service purpose and carries out “SUPRIOR QUALITY LOW PRICE” business philosophy. The advantaged technology,good quality of the machines and immediate after sale service are admired by most customers. Owin cnc will spare no effort to supply the best quality,the most high performance,the most competitive products and better service for all customers.

As we all know,the most important and expensive parts is fiber laser source for the fiber laser cutting machine. There is three kinds of brands fiber laser source popular using in the market now.

 

The first is Germany IPG fiber laser source.It is the most expensive brand under the same power.The cutting accuracy is also superior.

The second is Chinese Raycus fiber laser source,which is the most economical and practical model.And it is chosen by more customers now.

No matter for the quality or the price,Raycus is the best choice,which is the brand we used the most until now.

The third is Chinese Max fiber laser source,which is the cheapest model compared with IPG and Raycus based on the same power. If customers want to same a little money,Max is good choice. But it is also stable quality. If quality is not good,we never recommend to any customers.

These three brands fiber laser source are chosen by most factories,not  just our factories.So they are stood the test of the time.

 

Here is the cutting parameters of different power of Raycus for your reference:

Raycus 1000W

Materials

Thickness

(mm)

Speed

(m/min)

Pressure

(MPA)

Gas

Cutting height

(mm)

Stainless

steel

0.5

>24

1

N2

0.6

1

17~21

>1.1

N2

0.6

2

5.4~7.2

>1.5

N2

0.6

3

2.1~3

>2.0

N2

0.6

4

0.8~1.5

>2.0

N2

0.6

5

0.6~0.9

>2.0

N2

0.6

Carbon

steel

1

15~18

1

O2

1

2

5.1~6

0.5~0.8

O2

1

3

3.5~4.2

0.25~0.4

O2

1

4

2.3~2.7

0.15~0.2

O2

1

5

1.7~2.1

0.15~0.2

O2

1

6

1.2~1.8

0.10~0.15

O2

1

8

0.9~1.1

0.10~0.15

O2

1

10

0.6~0.72

0.10~0.15

O2

1

Raycus 1500W

Materials

Thickness

(mm)

Speed (m/min)

Pressure

(MPA)

Gas

Cutting height

(mm)

Stainless

Steel

1

25

1

N2

0.6

2

7

1.4

0.6

3

4

1.8

0.6

4

2

1.8

0.6

5

1.3

2

0.6

6

0.7

2

0.6

Carbon

steel

1

25

1

O2

1

3

4

0.12

1

6

1.6

0.14

1

8

1.2

0.14

1

10

1

0.16

1

12

0.8

0.18

1

14

0.6

0.2

1

16

0.5

0.05

1

Aluminum

1

16

1.2

 

0.6

2

6

1.4

 

0.6

3

2.5

1.8

N2

0.6

4

1.3

2

0.6

Brass

2

4

1.6

 

0.6

3

1.5

1.8

 

0.6

Copper

2

2

1

 

0.6

 Raycus 2000W

Materials

Thickness

(mm)

Speed (m/min)

Pressure (MPA)

Gas

Cutting height

(mm)

Stainless

steel

0.5

>30

1

N2

0.6

1

24~27

>1.1

0.6

2

9~11

>1.5

0.6

3

5.1~6

>2.0

0.6

4

3~3.6

>2.0

0.6

5

1.5~2.1

>2.0

0.6

6

0.9~1.2

>2.0

1

8

0.5~0.6

>2.0

1

Carbon steel

3

4.2~4.8

1

O2

1

5

3~3.3

0.5~0.8

1

6

2.1~2.7

0.25~0.4

1

8

1.2~1.8

0.15~0.2

1

10

1.1~1.5

0.15~0.2

1

12

0.96~1.2

0.10~0.15

1

14

0.9~1.1

0.10~0.15

1

16

0.78~0.9

0.10~0.15

1

20

0.6~72

0.10~0.15

1

 Raycus 3000W

Materials

Thickness

(mm)

Speed
(m/min)

Pressure

(MPA)

Gas

Cutting height
(mm)

Power using
(%)

Nozzle

Carbon steel

1

10.8

   9 bra

O2

1

25

2.0(double)

2

6.6

   5 bra

1

35

2.0(double)

3

4.2

1.4 bra

1

90

1.0(double)

4

3.6

1.4 bra

1

98

1.0(double)

6

2.4

1.0 bra

1

98

1.0(double)

8

1.8

0.8 bra

1

98

2.5(double)

10

1.1

0.6 bra

1

60

3.0(double)

12

0.9

0.6 bra

1

80

3.0(double)

14

0.8

0.6 bra

1

60

3.5(double)

16

0.72

0.7 bra

1

70

4.0(double)

18

0.65

0.8 bra

1

80

4.5(double)

20

0.6

0.8 bra

1

80

4.5(double)

22

0.6

0.8 bra

1

75

3.5(double)

Stainless steel

1

42

1.6 Mpa

N2

0.6

100

2.0(single)

2

12

1.6 Mpa

0.6

100

2.0(single)

3

9

2.0 Mpa

0.6

100

2.0(single)

4

6

2.0 Mpa

0.6

100

2.0(single)

6

2.1

2.4 Mpa

0.6

100

3.0(single)

8

1.2

2.4 Mpa

0.6

100

4.0(single)

10

0.9

2.4 Mpa

0.6

100

4.0(single)

Brass

1

21

1.2 Mpa

N2

0.6

100

2.0(single)

2

12

1.6 Mpa

0.6

100

2.0(single)

3

6

1.6 Mpa

0.6

100

2.0(single)

4

3.6

1.8 Mpa

0.6

100

2.0(single)

5

2.4

1.8 Mpa

0.6

100

3.0(single)

6

1.5

1.8 Mpa

0.6

100

3.0(single)

8

0.6

2.0 Mpa

0.6

100

3.0(single)

Aluminum

1.5

24

1.6 Mpa

N2

0.6

100

2.0(single)

2.5

9.6

2.0 Mpa

0.6

100

2.0(single)

3

7.2

2.0 Mpa

0.6

100

2.0(single)

4

3.6

2.0 Mpa

0.6

100

3.0(single)

5

2.4

2.0 Mpa

0.6

100

3.0(single)

6

1.8

2.4 Mpa

0.6

100

3.0(single)

8

0.9

2.4 Mpa

0.6

100

3.0(single)

As we all know,the most important and expensive parts is fiber laser source for the fiber laser cutting machine. There is three kinds of brands fiber laser source popular using in the market now.

 

The first is Germany IPG fiber laser source.It is the most expensive brand under the same power.The cutting accuracy is also superior.

The second is Chinese Raycus fiber laser source,which is the most economical and practical model.And it is chosen by more customers now.

No matter for the quality or the price,Raycus is the best choice,which is the brand we used the most until now.

The third is Chinese Max fiber laser source,which is the cheapest model compared with IPG and Raycus based on the same power. If customers want to same a little money,Max is good choice. But it is also stable quality. If quality is not good,we never recommend to any customers.

These three brands fiber laser source are chosen by most factories,not  just our factories.So they are stood the test of the time.

 

Here is the cutting parameters of different power of Raycus for your reference:

Raycus 1000W

Materials

Thickness

(mm)

Speed

(m/min)

Pressure

(MPA)

Gas

Cutting height

(mm)

Stainless

steel

0.5

>24

1

N2

0.6

1

17~21

>1.1

N2

0.6

2

5.4~7.2

>1.5

N2

0.6

3

2.1~3

>2.0

N2

0.6

4

0.8~1.5

>2.0

N2

0.6

5

0.6~0.9

>2.0

N2

0.6

Carbon

steel

1

15~18

1

O2

1

2

5.1~6

0.5~0.8

O2

1

3

3.5~4.2

0.25~0.4

O2

1

4

2.3~2.7

0.15~0.2

O2

1

5

1.7~2.1

0.15~0.2

O2

1

6

1.2~1.8

0.10~0.15

O2

1

8

0.9~1.1

0.10~0.15

O2

1

10

0.6~0.72

0.10~0.15

O2

1

Raycus 1500W

Materials

Thickness

(mm)

Speed (m/min)

Pressure

(MPA)

Gas

Cutting height

(mm)

Stainless

Steel

1

25

1

N2

0.6

2

7

1.4

0.6

3

4

1.8

0.6

4

2

1.8

0.6

5

1.3

2

0.6

6

0.7

2

0.6

Carbon

steel

1

25

1

O2

1

3

4

0.12

1

6

1.6

0.14

1

8

1.2

0.14

1

10

1

0.16

1

12

0.8

0.18

1

14

0.6

0.2

1

16

0.5

0.05

1

Aluminum

1

16

1.2

 

0.6

2

6

1.4

 

0.6

3

2.5

1.8

N2

0.6

4

1.3

2

0.6

Brass

2

4

1.6

 

0.6

3

1.5

1.8

 

0.6

Copper

2

2

1

 

0.6

 Raycus 2000W

Materials

Thickness

(mm)

Speed (m/min)

Pressure (MPA)

Gas

Cutting height

(mm)

Stainless

steel

0.5

>30

1

N2

0.6

1

24~27

>1.1

0.6

2

9~11

>1.5

0.6

3

5.1~6

>2.0

0.6

4

3~3.6

>2.0

0.6

5

1.5~2.1

>2.0

0.6

6

0.9~1.2

>2.0

1

8

0.5~0.6

>2.0

1

Carbon steel

3

4.2~4.8

1

O2

1

5

3~3.3

0.5~0.8

1

6

2.1~2.7

0.25~0.4

1

8

1.2~1.8

0.15~0.2

1

10

1.1~1.5

0.15~0.2

1

12

0.96~1.2

0.10~0.15

1

14

0.9~1.1

0.10~0.15

1

16

0.78~0.9

0.10~0.15

1

20

0.6~72

0.10~0.15

1

 Raycus 3000W

Materials

Thickness

(mm)

Speed
(m/min)

Pressure

(MPA)

Gas

Cutting height
(mm)

Power using
(%)

Nozzle

Carbon steel

1

10.8

   9 bra

O2

1

25

2.0(double)

2

6.6

   5 bra

1

35

2.0(double)

3

4.2

1.4 bra

1

90

1.0(double)

4

3.6

1.4 bra

1

98

1.0(double)

6

2.4

1.0 bra

1

98

1.0(double)

8

1.8

0.8 bra

1

98

2.5(double)

10

1.1

0.6 bra

1

60

3.0(double)

12

0.9

0.6 bra

1

80

3.0(double)

14

0.8

0.6 bra

1

60

3.5(double)

16

0.72

0.7 bra

1

70

4.0(double)

18

0.65

0.8 bra

1

80

4.5(double)

20

0.6

0.8 bra

1

80

4.5(double)

22

0.6

0.8 bra

1

75

3.5(double)

Stainless steel

1

42

1.6 Mpa

N2

0.6

100

2.0(single)

2

12

1.6 Mpa

0.6

100

2.0(single)

3

9

2.0 Mpa

0.6

100

2.0(single)

4

6

2.0 Mpa

0.6

100

2.0(single)

6

2.1

2.4 Mpa

0.6

100

3.0(single)

8

1.2

2.4 Mpa

0.6

100

4.0(single)

10

0.9

2.4 Mpa

0.6

100

4.0(single)

Brass

1

21

1.2 Mpa

N2

0.6

100

2.0(single)

2

12

1.6 Mpa

0.6

100

2.0(single)

3

6

1.6 Mpa

0.6

100

2.0(single)

4

3.6

1.8 Mpa

0.6

100

2.0(single)

5

2.4

1.8 Mpa

0.6

100

3.0(single)

6

1.5

1.8 Mpa

0.6

100

3.0(single)

8

0.6

2.0 Mpa

0.6

100

3.0(single)

Aluminum

1.5

24

1.6 Mpa

N2

0.6

100

2.0(single)

2.5

9.6

2.0 Mpa

0.6

100

2.0(single)

3

7.2

2.0 Mpa

0.6

100

2.0(single)

4

3.6

2.0 Mpa

0.6

100

3.0(single)

5

2.4

2.0 Mpa

0.6

100

3.0(single)

6

1.8

2.4 Mpa

0.6

100

3.0(single)

8

0.9

2.4 Mpa

0.6

100

3.0(single)